Why Is My QR Code Not Scanning? 10 Fixes

Work down this list from top to bottom. The first three cause most failures.

Re-make your QR code

Updated 19 November 2026 · 5 min read

Short answer

A QR code usually fails to scan because it is too small, has low contrast (or light-on-dark colors), has its white border cropped, holds too much data, or has a logo that is too big. If the code scans but the page does not load, the link is broken or the service behind the code is offline. Fix the cause and test with two phones.

Start here: does the scan fail, or does the page fail?

These are two different problems, and people mix them up.

  • The camera does not react at all: the code itself is the problem. Go to the table below.
  • The camera shows a link but the page is wrong or broken: the code is fine. The link or the service behind it is the problem. Open the link in a browser and see.

Fault-finding table (code not reading)

CauseHow to spot itFix
Printed too smallWorks up close, fails at normal distanceUse the 10:1 rule from the size guide
Low contrastPastel or similar colorsDark code on light background
Inverted colorsLight squares on dark backgroundSwitch back to dark on light
Border croppedNo white margin around the codeRestore at least 4 squares of margin
Too much dataThe pattern looks very denseShorten the link, see data limits
Logo too bigLogo covers much of the centerSmaller, simpler logo or none
Stretched or skewedSquares are not squareKeep the aspect ratio locked
Glare or glossy surfaceFails only at some anglesMatte finish, move the code
Blurry print or low-res PNGEdges look soft when zoomed inPrint from SVG
Curved or creased surfaceCode wraps over a bendPlace on a flat area

When the code scans but the page does not open

  1. Read the link shown in the camera banner. Copy it into a browser.
  2. If it shows an error, the page was moved or deleted. Restore it or make a new code.
  3. If the link goes to a redirect service, check that the service is still active. See do QR codes expire.
  4. If you used a typo in the link, fix it and print again. Check for missing https:// and extra spaces.

Special cases

  • WiFi code: check the network name for capital letters and the password for typos. Keep tracking off so the phone can join directly. See the WiFi guide.
  • UPI code: a wrong UPI ID shows an error in the payment app. Confirm the ID and test with a small payment. See the UPI guide.
  • Older phone: use Google Lens or a scanner app.

If you are the scanner, not the creator

Hold the phone still, 15 to 30 cm away. Add light. Tilt away from glare. Tap the code on the screen to focus. Then see how to scan a QR code for phone-specific steps.

A test routine that catches most problems

  1. Scan on screen.
  2. Print one copy at final size.
  3. Scan the print with an iPhone and an Android phone.
  4. Scan in dim light and at arm's length.
  5. Only then order the full print run.

Frequently asked questions

Why is my QR code not scanning?

The usual causes are a code that is too small, low contrast or inverted colors, a cropped white border, too much data, or a logo that is too big.

Why does my QR code scan but show an error page?

The code is fine, but the link is wrong, the page was deleted, or the redirect service behind the code is off. Open the link in a browser to check.

Do QR codes work in the dark or low light?

Phones can scan in dim light, but contrast helps a lot. Use a dark code on a light background and turn on the flashlight if needed.

Can a damaged QR code still scan?

Often yes. QR codes include error correction, so a small tear or smudge can be repaired by the scanner. Heavy damage can make it unreadable.

Why will my QR code not scan on some phones?

Older phones may not read QR codes in the camera app, and some scanners cannot read inverted colors. Use dark on light and test on more than one device.